| TOOL NUMBERS | DESCRIPTIONS |
| 5700 Retriever Scanner | The Ultimate Diagnostic Tool (for more information please click on the tool name) |
| CO 021 "Cobra" LiteOff | Turn off Service and Inspection indicators, turn off airbag
indicator, reset airbag faults |
| Palm Scanner | For
Recalling/Resetting fault codes on the Engine, ABS, SRS, A/T, A/C...
etc.systems. It also Reset Service light Applicable: BMW from 1988 |
| BMW 6221 Remote Starter Switch | Plug directly into 15 or 20 pin diagnostic socket to start
engine while adjusting valves or timing. Applicable: All BMW Models from 1981 to present. |
| BMW 6214 SRS Fault Code Reader | Reads encoded codes from multiplex
signal of diagnostic Complete operating instructions are included Applicable: Model E 23, 24, 30, 32, 34, Airbag1 and 2 system |
| BMW 6212 Service Light Reset Tool | Use it to turn off service lights on dash board. Applicable: BMW 4 and 6 cylinder 1983 and newer models equipped with either small or large diagnostic plug. |
| OR 300 Service Light Reset Tool | Multi Oil/Service light reset tool for BMW, Mercedes-Benz, Volvo, VW/Audi |
| BMW 2336 Rear Axle Carrier Bushing Remover/Installer Set | For more information please click on the tool name.
 Applicable: E23, E24, E28, E30, E32, E34 and E36 models |
| BMW 334-190 Rear Wheel Carrier R&R Kit | For
removing/installing ball joint at Rear Wheel Carrier (Lower Steering
Knuckle). Bushing # 040 060 038 012 # 33321090504, # 33321095631 Applicable BMW E38, E39, E52, E53, Click here for user instruction |
| BMW 38-39 Front Axle Trailing Arm R & R Set | For removing
and installing the rubber mount in the front trailing arm (traction strut)
right on the car. Available in Hydraulic (Use it together with
SPX
Hydraulic pump)
Bushing # 31120006482, 31129068753 Applicable: E 38, E 39
Click here for user instruction |
| BMW 137-806 Rear Axle Trailing Arm R&R Kit | For removing/installing the rubber mount in the rear trailing arm. (Bushing #
33321097009) Applicable: BMW E36 1995 and up
Click here for user instruction |
| BMW 7252
Ball Joint Remover / Installer Set Click here for instruction |
For removing and installing the outer
wheel control arm ball joint. Use it together with C Clamp (TW 35504 or OTC 7249) on the car, or with your hydraulic press. Applicable: E30 and E36 models (Ball Joint # 31126758510) |
| BMW 7253 Center Ball Joint Remover / Installer Set | Designed to remove and install the
center ball joint of the control arm.
Use it together with C Clamp (TW 35504 or OTC 7249) on the car, or with your hydraulic press. Center ball joint available! Applicable: E30,E36 models |
| BMW 7254 Thrust Arm (Bracket) Remover | Designed to remove the thrust arm
(bracket) from the front control arm.
Applicable: E30 (Bushing# 31129058931, E36, Z3 (Bushing# 31129059288) E46 (Bushing# 31126754547) models |
| BMW 7254-2 Thrust Arm (Bracket) Installer | Designed to install the thrust arm
(bracket) to the front control arm.
Applicable: E30 , E36, Z3, E46 models |
| BMW 7249-2B Arbor | For on-the-press R & R of the
thrust
arm bushings. Applicable: E 30, E36 |
| BMW 325-7 Valve Guide Installer | 7 mm Valve Guide installer Applicable: BMW 325 |
| BMW 113-240 Camshaft Locating Fixture | Aligns and holds camshaft in place when
assembling timing chain. Use it together with BMW112-300 locking pin. Applicable: BMW Model M42 (318i), M 44, M50, M52 |
| BMW 113-190 Camshaft Locating Fixture | Aligns and holds camshaft in
place when assembling timing chain. Use it together with BMW112-300 locking
pin. Applicable: BMW Model M40, M43TU For V-12 engines you must buy 2 blocks and the locking pin |
| BMW 113-292 Locking Pin | For secondary chain tensioner to block
chain tensioner piston e.g. when removing and installing sprockets Applicable: BMW Engine M50, M52 |
| BMW 115-490 Sprocket | For turning sprockets when removing and
installing VANOS unit Applicable: BMW Engine M50, M52, S50US, S52US |
BMW 113-390 Chain Tensioner |
For tensioning primary chain when
adjusting valve timing Applicable: BMW Engine M50, M60, M62 S50 B30 |
| BMW 114-220 Chain Tensioner | For tensioning primary chain when
adjusting valve timing Applicable: BMW Engine M52 |
| BMW 113-450 Banjo Fitting | Compressed air connection for checking
VANOS adjustment unit Applicable: BMW Engine M50, M52 |
| BMW 112-300 Lock pin | For locating crankshaft in ignition TDC
position in order to adjust valve timing. Applicable: BMW Engine M21, M40, M41, M42, M43, M44, M50, M51, M52, M60, M62, M70, M73, S50B30, S50B32 |
| BMW 112-440 Camshaft Locating Tool Set | Locking Fixture for fixing camshaft in
position when adjusting valve timing Kit including: Gauge for inlet side 1...4, Gauge for inlet side 5...8, 2 pcs fastening plate, 2 pcs special screw, Gauge for exhaust side 1..4, Gauge for exhaust side 5...8, Use it together with BMW112-300 locking pin. Applicable: BMW Engine M60, M62 (Operating instruction included) |
| BMW 113-440 Locking Fixture | For vibration amper 45 o- before TDC
position when installing cylinder head (this prevents valves making contact with piston) Applicable: M60 |
| BMW 37 Timing Chain Replacing Tool | Holds chain tight against cam sprocket
so chain can’t slip during installation.
Turns a 4 hour job into a 1 1/2 hour one-person job. Applicable: BMW 4 and 6 cylinder Models |
| BMW 312-140 Strut Removal Tool | Use to remove thrust strut from track
arm. Applicable: Model E 32, E 34 |
| BMW 267 Puller | Use for ball joints of drag link and tie
rod. Applicable: All BMW Models |
| BMW 344-000 Special Allen Key | Use to remove and install hand brake
shoe mount spring and ABS pulse transmitter. Applicable: All BMW Models |
| BMW 600-143 Special Screwdriver | Five sided screwdriver to release
anti-theft radio mounts. Applicable: All BMW Models |
| BMW 112-100 Flywheel Lock - Manual | Holder for locking flywheel with
transmission installed. Applicable: BMW Engine M10, Transm:3 HP 12, 3 HP 22 |
| BMW 112-120 Flywheel Lock - Automatic - | Holder for locking flywheel with
transmission installed. Applicable: BMW Engine M30 Transm: 3 HP 20, 3 HP 22, 4 HP 22 |
| BMW 112-170 Flywheel Lock | Holder for locking flywheel
with transmission installed. Applicable: BMW Engine M20, M21, M40, M41, M42, M43, M44, M50, M51, M52, S50B30, S50B32 |
| BMW 115-010 Water Pump Clamp | It holds linkage when removing water
pump. Use it with BMW 115-030 and 32mm wrench. Applicable: All BMW engines |
| BMW 115-030 Fan Pulley Holder | For removing water pumps on models with
temperature dependent viscosity drive fans. Model year: as of 80 Use it together with 32 mm open ended wrench. Applicable: BMW Engines M10, M20, M21, M30, M50, M51, M52, M70, M73, S14, S38, S50B30, S50B32 with 32 mm fan clutch nut |
| BMW 115-050/M Fan Pulley Holder | For removing water pumps on models with
temperature dependent viscosity drive fans. Applicable: BMW Eng. M40, M41, M42, M60, M62 |
| TST 3265/32 Open end Head | For
holding fan clutch nut on BMW Used in conjunction with
tool # BMW 115-030, Applicable: BMW M10, M20, M30 engine |
| BMW 321-110 Pin Wrench | Use it to remove slotted nut on cylinder
tube to renew seals on steering rack. Applicable: BMW E 30 |
| M 103-0037 Spark Plug Boot Pliers | Specially designed pliers allows for a
strong grip while safely removing spark plug wire boots. This pliers will not damage the
thin metal shielding. 8" needle nose pliers. Applicable: All BMW models with these type of wires. |
| TTS1005 Adapter Kit | Universal Radiator Adapter Kit |
| BMW 245, BMW 246,BMW 345, BMW 45Cooling System Adapters | To pressurize cooling systems. For more information please click on the tool name. |
| BMW 131-100 C.O. Hex Head Screw Driver - 5 mm | Adjust idle mixture control in place. Short body with a step
to engage diaphram and knurled handle for comfortable grip to insure easy adjustment. Applicable: L-Jetronic equipped BMW automobiles from 1983 |
| H 2901G-7mm Hex head Hinge Joint Socket | For inside hexagon mounting screws of backward caliper. Applicable: BMW 3 and 8 series |
| BMW 112-140 Flywheel Lock | Holder for locking flywheel with transmission removed. Applicable: BMW Engine M 10 - 4 cylinder |
| BMW 112-160 Flywheel Lock | Holder for locking flywheel with transmission removed. Applicable: BMW Engine M10, M30, S14, S38 - 6 cylinder |
| S1067 Head Bolt socket | Special lock ball
Torx socket for cylinder head screws on late
BMW 4-valve models. Applicable: M 40 from '89 & m 50 from '90 |
| KOKEN 3305 Spark Plug Socket | 18mm, 12 point deep socket Applicable: BMW 12 Cylinder engines |
| BMW 070 Valve Adjusting Tool | Use it to turn eccentric valve adjuster. Applicable: All BMW models (except M series) |
| BMW 113-170 Vale Tappet Loading lever | Depress valve
tappets for easy removal of valve adjusting shims. Applicable: S14, S38 (M3, M5, M6 USA Models) |
| KOKEN 2010-5 / H8501-5 Allen Socket | 5 MM, 1/4" Drive to remove the fuse box cover. Available
in Koken or Hazet Applicable: BMW 1995 7 series |
| S 3049-7 Allen Socket | The short length of this socket (24 mm) allows for easy
removal of the rear brake caliper slide bolts. Applicable: BMW models E36 (newer 3 series) and E31 (8 series) |
| S 51-30 Extra Deep Socket | 30 mm, 12 point 1/2" Drive deep socket for R & R of
transmission drive shaft flange nut and pinion drive shaft flange nut on differential. Applicable: BMW models |
| S 55-36 Socket | 36 mm, 6 point drive socket, use it to R & R front wheel
bearing retainer nut. Applicable: BMW 1984 & newer 3 series |
| S 55-46 Socket | 46 mm, 12 point drive socket, use it to R & R front wheel
bearing retainer nut. Applicable: BMW 1983 & newer 5, 6 and 7 series |
| S 3676 / H 2760 Wrench | 14 x 17 mm, used for
R & R of oil filler plug on
differential. Available in Hazet or Stahlwille. Applicable: All BMWs 1991 and newer |